Interfacial microstructure and mechanical properties of Ti3SiC2 ceramic and TC11 alloy joint diffusion bonded with a Cu interlayer

Reliable joints of Ti₃SiC₂ ceramic and TC11 alloy were diffusion bonded with a 50 μm thick Cu interlayer. The typical interfacial structure of the diffusion boned joint, which was dependent on the interdiffusion and chemical reactions between Al, Si and Ti atoms from the base materials and Cu interlayer, was TC11/α-Ti + β-Ti + Ti₂Cu + TiCu/Ti₅Si₄ + TiSiCu/Cu(s, s)/Ti₃SiC₂. The influence of bonding temperature and time on the interfacial structure and mechanical properties of Ti₃SiC₂/Cu/TC11 joint was analyzed. With the increase of bonding temperature and time, the joint shear strength was gradually increased due to enhanced atomic diffusion. However, the thickness of Ti₅Si₄ and TiSiCu layers with high microhardness increased for a long holding time, resulting in the reduction of bonding strength. The maximum shear strength of 251 ± 6 MPa was obtained for the joint diffusion bonded at 850 °C for 60 min, and fracture primarily occurred at the diffusion layer adjacent to the Ti₃SiC₂ substrate. This work provided an economical and convenient solution for broadening the engineering application of Ti₃SiC₂ ceramic.     

Structural,electronic paramagnetic resonance and magnetic properties of praseodymium-doped rare earth CeO2 semiconductors

In this work, praseodymium (Pr) doped cerium oxide (CeO₂) was prepared using the microwave-assisted hydrothermal method (MAH) and the properties were investigated by X-ray diffraction analysis (XRD), Raman spectroscopy, Field Emission Gun Scanning Electron Microscope (FEG-SEM), BET method, Photoluminescence spectroscopy (PL), Fourier-transform infrared spectroscopy (FTIR), Ultraviolet–visible spectroscopy (UV–Vis), Electron paramagnetic resonance spectroscopy (EPR) and Magnetometry. The results showed that increasing the Pr-doping promotes a structural disorder due to increased oxygen vacancies. XRD confirmed a cubic structure without deleterious phases with modifications in the structure caused by alteration in the cerium oxidation state as well as changes in the crystallite size and strain obtained by Wellinson-Hall method. Raman spectroscopy shows that changing the Pr content results in samples with different defect densities at short range. FEG-SEM showed that the nanocrystals are agglomerated with small particles tend to aggregate spontaneously to decrease the surface energy. BET method showed that the Pr doping results in a gain of specific surface area. PL indicated that Pr³⁺ leads to distinct emissions; red emission associated to oxygen vacancies located near the conduction band (shallow defects), green emission associated to electron-hole recombination and orange emission associated to shallow defects and electron-hole recombination. FTIR indicated the complete process of nucleation with no other phase. UV–Vis showed the transitions between oxygen 2p, cerium 4f and praseodymium 4f states. The EPR signal shows events occurring around 344 mT. These events can be related due the presence of paramagnetic elements containing unpaired electrons, such as Ce (III), which is indicative of cerium reduction caused by Pr ions, as evidenced by Rietveld data. Regardless of the Pr concentration used in this research, the magnetic measurements show a superparamagnetic system below the blocking temperature of ~20 K and a paramagnetic system above this temperature, which indicates no significant changes in the average size of the nanoparticles. Surface area, crystallite size and the temperature are important parameters, which control the magnetic properties of such N-type semiconductors.     

A Comprehensive Review of Genetically Engineered Mouse Models for Prader-Willi Syndrome Research

Prader-Willi syndrome (PWS) is a neurogenetic multifactorial disorder caused by the deletion or inactivation of paternally imprinted genes on human chromosome 15q11-q13. The affected homologous locus is on mouse chromosome 7C. The positional conservation and organization of genes including the imprinting pattern between mice and men implies similar physiological functions of this locus. Therefore, considerable efforts to recreate the pathogenesis of PWS have been accomplished in mouse models. We provide a summary of different mouse models that were generated for the analysis of PWS and discuss their impact on our current understanding of corresponding genes, their putative functions and the pathogenesis of PWS. Murine models of PWS unveiled the contribution of each affected gene to this multi-facetted disease, and also enabled the establishment of the minimal critical genomic region (PWScr) responsible for core symptoms, highlighting the importance of non-protein coding genes in the PWS locus. Although the underlying disease-causing mechanisms of PWS remain widely unresolved and existing mouse models do not fully capture the entire spectrum of the human PWS disorder, continuous improvements of genetically engineered mouse models have proven to be very powerful and valuable tools in PWS research.     

Sorption of meso-Phenylporphyrin Iodide on Polystyrene–Bentonite Film Composites

Protection of Metals and Physical Chemistry of Surfaces - Modification of polystyrene (PS) with bentonite was carried out, and film materials with improved sorption properties toward...     

Laboratory Studies to Determine Suitable Chemicals to Improve Oil Recovery from Garzan Oil Field

Garzan oil field is located at the south east of Turkey. It is a mature oil field and the reservoir is fractured carbonate reservoir. After producing about 1% original oil in place (OOIP) reservoir pressure started to decline. Waterflooding was started in order to support reservoir pressure and also to enhance oil production in 1960. Waterflooding improved the oil recovery but after years of flooding water breakthrough at the production wells was observed. This increased the water/oil ratio at the production wells. In order to enhance oil recovery again different techniques were investigated. Chemical enhanced oil recovery (EOR) methods are gaining attention all over the world for oil recovery. Surfactant injection is an effective way for interfacial tension (IFT) reduction and wettability reversal. In this study, 31 different types of chemicals were studied to specify the effects on oil production. This paper presents solubility of surfactants in brine, IFT and contact angle measurements, imbibition tests, and lastly core flooding experiments. Most of the chemicals were incompatible with Garzan formation water, which has high divalent ion concentration. In this case, the usage of 2-propanol as co-surfactant yielded successful results for stability of the selected chemical solutions. The results of the wettability test indicated that both tested cationic and anionic surfactants altered the wettability of the carbonate rock from oil-wet to intermediate-wet. The maximum oil recovery by imbibition test was reached when core was exposed 1-ethly ionic liquid after imbibition in formation water. Also, after core flooding test, it is concluded that considerable amount of oil can be recovered from Garzan reservoir by waterflooding alone if adverse effects of natural fractures could be eliminated.     

Study and Development of Superhydrophobic Coatings Based on Silicon Dioxide

Glass Physics and Chemistry - It is found that the chemical composition of the surface cannot fully provide superhydrophobicity, as a combination of a hydrophobic material with an appropriate...     

Erratum to: Digital Twins of CNC Machine Tools in the Reconfiguring of Aircraft Factories

Russian Engineering Research - An Erratum to this paper has been published: https://doi.org/10.3103/S1068798X22100355     

Algorithm for Solving the Cauchy Problem for a Two-Dimensional Difference Equation with Initial Data Defined in a “Strip”

Programming and Computer Software - In this paper, we propose an algorithm for solving the Cauchy problem for a two-dimensional difference equation with constant coefficients at a point, based on...     

Choice of Activation Function in Convolutional Neural Networks for Person Re-Identification in Video Surveillance Systems

Programming and Computer Software - In this paper, we improve the accuracy of person re-identification in images obtained from distributed video surveillance systems by choosing activation...     

Hybrid Technology for Surface Hardening of Structural Steel

Russian Engineering Research - Hybrid surface hardening consisting of quenching with inductive heating by high-frequency current and subsequent ultrasonic surface plastic deformation is considered....